Skip to content

πŸ’‰ IV Bolus Single Dose ​

For IV Bolus administration of a single dose, the following parameters are calculated as described.

Parameters that do not depend on a terminal slope ​

Parameter nameParameter code in outputDescription of calculation
AUC all linear C0AUC_all_lin_C0Sum of partial AUC values for all time points including C0 using the linear method
AUC all linear C0/DoseAUC_all_lin_C0_DAUC_all_lin_C0Dose
AUC all linlog C0AUC_all_log_C0Sum of partial AUC values for all time points including C0 using the linear up log down method
AUC all linlog C0/DoseAUC_all_log_C0_DAUC_all_log_C0Dose
AUC last linear C0AUC_last_lin_C0Sum of partial AUC values from time of dose administration (C0) through TLAST using the linear method
AUC last linear C0/DoseAUC_last_lin_C0_DAUC_last_lin_C0Dose
AUC last linlog C0AUC_last_log_C0Sum of partial AUC values from time of dose administration (C0) through TLAST using the linear up log down method
AUC last linlog C0/DoseAUC_last_log_C0_DAUC_last_log_C0Dose
AUMC last linear C0AUMC_last_lin_C0Sum of partial AUMC values from time of dose administration (C0) through TLAST using the linear methd
AUMC last linlog C0AUMC_last_log_C0Sum of partial AUMC values from time of dose administration (C0) through TLAST using the linear up log down methd
C0C0Log-linear extrapolation back to time of dose administration using the first 2 measured concentration time point.
Last measurable concentrationClastAnalyzed concentration value greater than zero with the largest associated time value.
DoseDoseDose amount
MRT last linear C0MRT_last_lin_C0AUMC_last_lin_C0AUC_last_lin_C0
MRT last linlog C0MRT_last_lin_C0AUMC_last_log_C0AUC_last_log_C0
Number of BLQ samplesN_blqTotal number of observed concentrations reported as "BLQ"
Number of missing samplesN_missTotal number of observed concentrations reported as "Missing"
Number of samplesN_sampTotal number of records in the observed concentration column. Observations that are
Time of ClastTlastValue in the time column the corresponds to Clast.
Partial AUC from C0 linearpAUC_C0_linPartial area under the curve from C0 to the first measured timepoint using the linear method
Partial AUC from C0 linlogpAUC_C0_logPartial area under the cuver from C0 to the first measured timepoint using the linear up log down methd

Parameters that depend on a terminal slope ​

Parameter nameParameter code in outputDescription of calculation
Percent AUC extrapolated to C0 linearAUC_extrap_C0_lin100βˆ—[pAUC_C0_linAUC_inf_lin_C0]
Percent AUC extrapolated to C0 linlogAUC_extrap_C0_log100βˆ—[pAUC_C0_logAUC_inf_log_C0]
AUC infinity linear C0AUC_inf_lin_C0AUC_last_lin_C0+Clastkel
AUC infinity linear C0/DoseAUC_inf_lin_C0_DAUC_inf_lin_C0Dose
Percent extrapolated AUC infinity linear C0AUC_inf_lin_C0_extrap100βˆ—[AUC_inf_lin_C0βˆ’AUC_last_lin_C0AUC_inf_lin_C0]
AUC infinity linlog C0AUC_inf_log_C0AUC_last_log_C0+Clastkel
AUC infinity linlog C0/DoseAUC_inf_log_C0_DAUC_inf_log_C0Dose
Percent extrapolated AUC infinity linlog C0AUC_inf_log_C0_extrap100βˆ—[AUC_inf_lin_C0βˆ’AUC_last_log_C0AUC_inf_lin_C0]
AUMC infinity linear C0AUMC_inf_lin_C0AUMC_last_lin_C0+Clastβˆ—Tlastkel+Clastkel2
Percent extrapolated AUMC infinity linear C0AUMC_inf_lin_C0_extrap100βˆ—[AUMC_inf_lin_C0βˆ’AUMC_last_lin_C0AUMC_inf_lin_C0]
AUMC infinity linlogAUMC_inf_log_C0AUMC_last_log_C0+Clastβˆ—Tlastkel+Clastkel2
Percent extrapolated AUMC infinity linlog C0AUMC_inf_log_C0_extrap100βˆ—[AUMC_inf_log_C0βˆ’AUMC_last_log_C0AUMC_inf_log_C0]
CL linearCL_lin_C0DoseAUC_inf_lin_C0
CL linlogCL_log_C0DoseAUC_inf_log_C0
MRT last linearMRT_last_lin_C0AUMC_last_lin_C0AUC_last_lin_C0
MRT last linlogMRT_last_log_C0AUMC_last_log_C0AUC_last_log_C0
MRT linearMRT_lin_C0AUMC_inf_lin_C0AUC_inf_lin_C0
MRT linlogMRT_log_C0AUMC_inf_log_C0AUC_inf_log_C0
Vss linearVss_lin_C0MRT_lin_C0βˆ—CL_lin_C0
Vss linlogVss_log_C0MRT_log_C0βˆ—CL_log_C0
Vz linearVz_lin_C0Dosekelβˆ—AUC_inf_lin_C0
Vz linlogVz_log_C0Dosekelβˆ—AUC_inf_log_C0
Terminal slope groupgroupGroup number for each estimated terminal slope. For each profile at least one terminal slope is calculated. All parameters that are dependent on estimation of the terminal slope are also calcualted and given the same group number.
Terminal slope interceptinterceptIntercept of linear regression.
Terminal slopekelNegative of estimated slope by linear regression of the natural log-transformed analyzed concentrations and the time of each observation.
Terminal slope adjusted r-squaredkel_adjr21βˆ’(1βˆ’kel_r2)βˆ—[kel_nβˆ’1kel_nβˆ’2]
Terminal slope lower time pointkel_lowSmallest time value used to calculate the terminal slope.
Number of data points in terminal slope calculationkel_nNumber of samples included in teh terminal slope calculation.
Terminal slope r-squaredkel_r2r2 value from terminal slope linear regression.
Terminal slope spankel_spankel_upperβˆ’kel_lowkel_thalf
Terminal half lifekel_thalfln(2)kel
Terminal slope upper time pointkel_upperLargest time value used to calculate the terminal slope.